Assorted screwdrivers, both flathead and Phillips. Di-Electric grease to coat O-rings in case you run out. Commonly found at Auto Parts stores. Concrete bricks to hold down the non-pen mount. A set of Hex wrenches used for Allen bolts on the radio assembly. A bag of Snap-On F-Connectors for coax cables.
Rubber weather-sealing tape. Electrical tape. Wall-Plates for where the coax cables enter the server room. A coax wire stripper.
Wire cutters. Crimping tool for Snap-On connectors. A power screwdriver or drill. A Hole-Saw bit to drill holes for the cable run. A Masonry Drill Bit will be needed to drill through brick or a solid wall. This bit needs to be long and wide enough to penetrate the wall for all three cables.
Silicone Caulking is used to reseal exterior holes after cable runs are finished. Be sure to seal every hole you make into the exterior of a building! Twine or narrow string to help pull cables along ceilings. The whole saw should be used on both side of the wall for a clean looking wall penetration.
Satellite Equipment Leasing Leasing may include installation costs, and in some cases annual service costs. Satellite Equipment Leasing. Use Your Own iDirect Equipment. Ingress Definition This rating classifies the degrees of protection provided against the intrusion of solid objects, dust, accidental contact, and water in electrical enclosures, providing users with more detailed information than vague terms such as waterproof.
Ingress Definition. Satellite Installation Tools Having ALL of the right tools and supplies at the installation will keep you from turning a 1-day install into a 3 day install. Satellite Installation Tools and Equipment. Position them behind the support, then add the screws through them to bind the parts together. Part 3. Select a satellite you wish to connect to. Pick a satellite that is in range of your particular dish. There are numerous satellites out there, but dishes cannot get signals from all of them.
If you bought your dish from a TV service, for instance, you might have a hard time connecting to their competitor's satellites. Tracking sites list the names, which usually include the owning company or the service they provide. If you bought a satellite service, it is possible to receive satellite signals outside that service.
Since you usually need to replace several parts, it's easier to get a new satellite instead. Try to pick a satellite close to your area. If you subscribe to a particular TV service, you will need to use the company's satellites. The biggest providers have multiple satellites. Find the satellite's location before positioning the dish. You're going to need to point the dish in the correct direction, then angle it up at the sky.
This isn't easy to do if you don't know the satellite's positioning. Fortunately, satellites don't move much, so you can use a positioning database to adjust your dish. The site will give you the precise positioning needed for your dish to receive the signal. You won't be able to receive a signal from a distant satellite. Don't expect to reach a Chinese satellite if you're in North America, for instance. Use the azimuth number to rotate the satellite.
Have a compass handy and locate true north first. Then, look at the azimuth number and find where that is on the compass. North is considered 0 degrees, east is 90 degrees, south is degrees, and west is degrees. Rotate the satellite dish horizontally until it points in the correct direction. Then, turn the satellite southwest from there. Move the dish vertically to adjust its elevation. Once you know the height needed to reach the satellite, go behind the dish. Examine the end of the mount where it connects to the dish.
You will see a bolt inside a slot labeled by degrees, usually 10 to Loosen the bolt by twisting it counterclockwise, then reposition the dish to the proper elevation. Moving the bolt along the slot raises or lowers the dish. For instance, if the dish requires a degree elevation, it will point up into the sky almost as much as it possibly can. Slide the loosened bolt back toward the degree marker. Adjust the dish's polarization until you get a clear signal.
The final part that needs to be adjusted is LNB, responsible for receiving and sending the signal into your home. It is usually an arm on the front that points toward the dish. Test out the signal quality by hooking the dish up to the receiver and a TV, then loosen the connecting nut on the arm by turning it counterclockwise with a wrench.
If the TV is far away, have someone else stand near it and give you feedback. You may need to wait to adjust the LNB until you're done with the wiring. Take care of it before then, if you're able, so you don't have to keep climbing on the roof to make adjustments. The LNB can sometimes be controlled by turning a mount part on the back of the dish left or right.
Part 4. Check your home first for a previously-used cable opening. The dish's cable needs its own little space to enter your home and hook up to your TV. Unless your home is in the process of being built, drilling a single hole is the easiest way to do this.
Position your TV and the satellite receiver nearby to prepare for the connection. It needs to be below the frost line, the lowest point that freezes in winter, which is about 3 in 7. Run a coaxial cable from the LNB to the receiver.
Make sure the receiver is positioned close to the satellite to ensure the cable can reach it. TV service providers will also give you one when you buy a satellite from them. The coaxial cable sometimes connects to the back of the satellite. Usually, though, it plugs directly into the LNB. Once the cord is in place, your TV will be able to receive the satellite signal. Turn on the TV to see if it works. The receiver may plug directly into the TV instead. Consult a wiring guide for specific instructions on how to connect the satellite, receiver, and your TV.
If you bought the satellite from a TV service provider, they would also provide a wiring guide. Turn on the TV to test the signal. Press the satellite button if your remote has one or navigate to the settings menu. You should be able to get a picture right away.
If the signal quality is poor, make sure you positioned the satellite dish correctly. Adjust it to get the clearest possible signal! Please note the azimuth, elevation, and LNB numbers and compare them to the satellite's location. Include your email address to get a message when this question is answered. Ask TV service providers for an install. Many of them offer free installations as long as you buy a subscription for their service.
Helpful 2 Not Helpful 0. Find spots to hide loose cables in your home. If the satellite dish's cable is exposed, put furniture and other decorations in front of it. Helpful 1 Not Helpful 0. Every satellite receiver needs a separate coaxial cable. You can't split the cable, so you will need to find ways to route the cables all the way to the extra TVs you plan on setting up.
If you're running a coaxial cable outdoors along the ground, consider installing a grounding block and wire to protect the cable from static.
Helpful 1 Not Helpful 1. Submit a Tip All tip submissions are carefully reviewed before being published.
0コメント